1578 lines
36 KiB
Text
1578 lines
36 KiB
Text
|
menu "ARM architecture"
|
||
|
|
depends on ARM
|
||
|
|
|
||
|
|
config SYS_ARCH
|
||
|
|
default "arm"
|
||
|
|
|
||
|
|
config ARM64
|
||
|
|
bool
|
||
|
|
select PHYS_64BIT
|
||
|
|
select SYS_CACHE_SHIFT_6
|
||
|
|
|
||
|
|
if ARM64
|
||
|
|
config POSITION_INDEPENDENT
|
||
|
|
bool "Generate position-independent pre-relocation code"
|
||
|
|
help
|
||
|
|
U-Boot expects to be linked to a specific hard-coded address, and to
|
||
|
|
be loaded to and run from that address. This option lifts that
|
||
|
|
restriction, thus allowing the code to be loaded to and executed
|
||
|
|
from almost any address. This logic relies on the relocation
|
||
|
|
information that is embedded into the binary to support U-Boot
|
||
|
|
relocating itself to the top-of-RAM later during execution.
|
||
|
|
|
||
|
|
config SYS_INIT_SP_BSS_OFFSET
|
||
|
|
int
|
||
|
|
help
|
||
|
|
U-Boot typically uses a hard-coded value for the stack pointer
|
||
|
|
before relocation. Define this option to instead calculate the
|
||
|
|
initial SP at run-time. This is useful to avoid hard-coding addresses
|
||
|
|
into U-Boot, so that can be loaded and executed at arbitrary
|
||
|
|
addresses and thus avoid using arbitrary addresses at runtime. This
|
||
|
|
option's value is the offset added to &_bss_start in order to
|
||
|
|
calculate the stack pointer. This offset should be large enough so
|
||
|
|
that the early malloc region, global data (gd), and early stack usage
|
||
|
|
do not overlap any appended DTB.
|
||
|
|
|
||
|
|
config LINUX_KERNEL_IMAGE_HEADER
|
||
|
|
bool
|
||
|
|
help
|
||
|
|
Place a Linux kernel image header at the start of the U-Boot binary.
|
||
|
|
The format of the header is described in the Linux kernel source at
|
||
|
|
Documentation/arm64/booting.txt. This feature is useful since the
|
||
|
|
image header reports the amount of memory (BSS and similar) that
|
||
|
|
U-Boot needs to use, but which isn't part of the binary.
|
||
|
|
|
||
|
|
if LINUX_KERNEL_IMAGE_HEADER
|
||
|
|
config LNX_KRNL_IMG_TEXT_OFFSET_BASE
|
||
|
|
hex
|
||
|
|
help
|
||
|
|
The value subtracted from CONFIG_SYS_TEXT_BASE to calculate the
|
||
|
|
TEXT_OFFSET value written in to the Linux kernel image header.
|
||
|
|
endif
|
||
|
|
endif
|
||
|
|
|
||
|
|
config STATIC_RELA
|
||
|
|
bool
|
||
|
|
default y if ARM64 && !POSITION_INDEPENDENT
|
||
|
|
|
||
|
|
config DMA_ADDR_T_64BIT
|
||
|
|
bool
|
||
|
|
default y if ARM64
|
||
|
|
|
||
|
|
config HAS_VBAR
|
||
|
|
bool
|
||
|
|
|
||
|
|
config HAS_THUMB2
|
||
|
|
bool
|
||
|
|
|
||
|
|
# Used for compatibility with asm files copied from the kernel
|
||
|
|
config ARM_ASM_UNIFIED
|
||
|
|
bool
|
||
|
|
default y
|
||
|
|
|
||
|
|
# Used for compatibility with asm files copied from the kernel
|
||
|
|
config THUMB2_KERNEL
|
||
|
|
bool
|
||
|
|
|
||
|
|
config SYS_ARM_CACHE_CP15
|
||
|
|
bool "CP15 based cache enabling support"
|
||
|
|
help
|
||
|
|
Select this if your processor suports enabling caches by using
|
||
|
|
CP15 registers.
|
||
|
|
|
||
|
|
config SYS_ARM_MMU
|
||
|
|
bool "MMU-based Paged Memory Management Support"
|
||
|
|
select SYS_ARM_CACHE_CP15
|
||
|
|
help
|
||
|
|
Select if you want MMU-based virtualised addressing space
|
||
|
|
support by paged memory management.
|
||
|
|
|
||
|
|
config SYS_ARM_MPU
|
||
|
|
bool 'Use the ARM v7 PMSA Compliant MPU'
|
||
|
|
help
|
||
|
|
Some ARM systems without an MMU have instead a Memory Protection
|
||
|
|
Unit (MPU) that defines the type and permissions for regions of
|
||
|
|
memory.
|
||
|
|
If your CPU has an MPU then you should choose 'y' here unless you
|
||
|
|
know that you do not want to use the MPU.
|
||
|
|
|
||
|
|
# If set, the workarounds for these ARM errata are applied early during U-Boot
|
||
|
|
# startup. Note that in general these options force the workarounds to be
|
||
|
|
# applied; no CPU-type/version detection exists, unlike the similar options in
|
||
|
|
# the Linux kernel. Do not set these options unless they apply! Also note that
|
||
|
|
# the following can be machine specific errata. These do have ability to
|
||
|
|
# provide rudimentary version and machine specific checks, but expect no
|
||
|
|
# product checks:
|
||
|
|
# CONFIG_ARM_ERRATA_430973
|
||
|
|
# CONFIG_ARM_ERRATA_454179
|
||
|
|
# CONFIG_ARM_ERRATA_621766
|
||
|
|
# CONFIG_ARM_ERRATA_798870
|
||
|
|
# CONFIG_ARM_ERRATA_801819
|
||
|
|
# CONFIG_ARM_CORTEX_A8_CVE_2017_5715
|
||
|
|
# CONFIG_ARM_CORTEX_A15_CVE_2017_5715
|
||
|
|
|
||
|
|
config ARM_ERRATA_430973
|
||
|
|
bool
|
||
|
|
|
||
|
|
config ARM_ERRATA_454179
|
||
|
|
bool
|
||
|
|
|
||
|
|
config ARM_ERRATA_621766
|
||
|
|
bool
|
||
|
|
|
||
|
|
config ARM_ERRATA_716044
|
||
|
|
bool
|
||
|
|
|
||
|
|
config ARM_ERRATA_725233
|
||
|
|
bool
|
||
|
|
|
||
|
|
config ARM_ERRATA_742230
|
||
|
|
bool
|
||
|
|
|
||
|
|
config ARM_ERRATA_743622
|
||
|
|
bool
|
||
|
|
|
||
|
|
config ARM_ERRATA_751472
|
||
|
|
bool
|
||
|
|
|
||
|
|
config ARM_ERRATA_761320
|
||
|
|
bool
|
||
|
|
|
||
|
|
config ARM_ERRATA_773022
|
||
|
|
bool
|
||
|
|
|
||
|
|
config ARM_ERRATA_774769
|
||
|
|
bool
|
||
|
|
|
||
|
|
config ARM_ERRATA_794072
|
||
|
|
bool
|
||
|
|
|
||
|
|
config ARM_ERRATA_798870
|
||
|
|
bool
|
||
|
|
|
||
|
|
config ARM_ERRATA_801819
|
||
|
|
bool
|
||
|
|
|
||
|
|
config ARM_ERRATA_826974
|
||
|
|
bool
|
||
|
|
|
||
|
|
config ARM_ERRATA_828024
|
||
|
|
bool
|
||
|
|
|
||
|
|
config ARM_ERRATA_829520
|
||
|
|
bool
|
||
|
|
|
||
|
|
config ARM_ERRATA_833069
|
||
|
|
bool
|
||
|
|
|
||
|
|
config ARM_ERRATA_833471
|
||
|
|
bool
|
||
|
|
|
||
|
|
config ARM_ERRATA_845369
|
||
|
|
bool
|
||
|
|
|
||
|
|
config ARM_ERRATA_852421
|
||
|
|
bool
|
||
|
|
|
||
|
|
config ARM_ERRATA_852423
|
||
|
|
bool
|
||
|
|
|
||
|
|
config ARM_ERRATA_855873
|
||
|
|
bool
|
||
|
|
|
||
|
|
config ARM_CORTEX_A8_CVE_2017_5715
|
||
|
|
bool
|
||
|
|
|
||
|
|
config ARM_CORTEX_A15_CVE_2017_5715
|
||
|
|
bool
|
||
|
|
|
||
|
|
config CPU_ARM720T
|
||
|
|
bool
|
||
|
|
select SYS_CACHE_SHIFT_5
|
||
|
|
imply SYS_ARM_MMU
|
||
|
|
|
||
|
|
config CPU_ARM920T
|
||
|
|
bool
|
||
|
|
select SYS_CACHE_SHIFT_5
|
||
|
|
imply SYS_ARM_MMU
|
||
|
|
|
||
|
|
config CPU_ARM926EJS
|
||
|
|
bool
|
||
|
|
select SYS_CACHE_SHIFT_5
|
||
|
|
imply SYS_ARM_MMU
|
||
|
|
|
||
|
|
config CPU_ARM946ES
|
||
|
|
bool
|
||
|
|
select SYS_CACHE_SHIFT_5
|
||
|
|
imply SYS_ARM_MMU
|
||
|
|
|
||
|
|
config CPU_ARM1136
|
||
|
|
bool
|
||
|
|
select SYS_CACHE_SHIFT_5
|
||
|
|
imply SYS_ARM_MMU
|
||
|
|
|
||
|
|
config CPU_ARM1176
|
||
|
|
bool
|
||
|
|
select HAS_VBAR
|
||
|
|
select SYS_CACHE_SHIFT_5
|
||
|
|
imply SYS_ARM_MMU
|
||
|
|
|
||
|
|
config CPU_V7A
|
||
|
|
bool
|
||
|
|
select HAS_THUMB2
|
||
|
|
select HAS_VBAR
|
||
|
|
select SYS_CACHE_SHIFT_6
|
||
|
|
imply SYS_ARM_MMU
|
||
|
|
|
||
|
|
config CPU_V7M
|
||
|
|
bool
|
||
|
|
select HAS_THUMB2
|
||
|
|
select SYS_ARM_MPU
|
||
|
|
select SYS_CACHE_SHIFT_5
|
||
|
|
select SYS_THUMB_BUILD
|
||
|
|
select THUMB2_KERNEL
|
||
|
|
|
||
|
|
config CPU_V7R
|
||
|
|
bool
|
||
|
|
select HAS_THUMB2
|
||
|
|
select SYS_ARM_CACHE_CP15
|
||
|
|
select SYS_ARM_MPU
|
||
|
|
select SYS_CACHE_SHIFT_6
|
||
|
|
|
||
|
|
config CPU_PXA
|
||
|
|
bool
|
||
|
|
select SYS_CACHE_SHIFT_5
|
||
|
|
imply SYS_ARM_MMU
|
||
|
|
|
||
|
|
config CPU_SA1100
|
||
|
|
bool
|
||
|
|
select SYS_CACHE_SHIFT_5
|
||
|
|
imply SYS_ARM_MMU
|
||
|
|
|
||
|
|
config SYS_CPU
|
||
|
|
default "arm720t" if CPU_ARM720T
|
||
|
|
default "arm920t" if CPU_ARM920T
|
||
|
|
default "arm926ejs" if CPU_ARM926EJS
|
||
|
|
default "arm946es" if CPU_ARM946ES
|
||
|
|
default "arm1136" if CPU_ARM1136
|
||
|
|
default "arm1176" if CPU_ARM1176
|
||
|
|
default "armv7" if CPU_V7A
|
||
|
|
default "armv7" if CPU_V7R
|
||
|
|
default "armv7m" if CPU_V7M
|
||
|
|
default "pxa" if CPU_PXA
|
||
|
|
default "sa1100" if CPU_SA1100
|
||
|
|
default "armv8" if ARM64
|
||
|
|
|
||
|
|
config SYS_ARM_ARCH
|
||
|
|
int
|
||
|
|
default 4 if CPU_ARM720T
|
||
|
|
default 4 if CPU_ARM920T
|
||
|
|
default 5 if CPU_ARM926EJS
|
||
|
|
default 5 if CPU_ARM946ES
|
||
|
|
default 6 if CPU_ARM1136
|
||
|
|
default 6 if CPU_ARM1176
|
||
|
|
default 7 if CPU_V7A
|
||
|
|
default 7 if CPU_V7M
|
||
|
|
default 7 if CPU_V7R
|
||
|
|
default 5 if CPU_PXA
|
||
|
|
default 4 if CPU_SA1100
|
||
|
|
default 8 if ARM64
|
||
|
|
|
||
|
|
config SYS_CACHE_SHIFT_5
|
||
|
|
bool
|
||
|
|
|
||
|
|
config SYS_CACHE_SHIFT_6
|
||
|
|
bool
|
||
|
|
|
||
|
|
config SYS_CACHE_SHIFT_7
|
||
|
|
bool
|
||
|
|
|
||
|
|
config SYS_CACHELINE_SIZE
|
||
|
|
int
|
||
|
|
default 128 if SYS_CACHE_SHIFT_7
|
||
|
|
default 64 if SYS_CACHE_SHIFT_6
|
||
|
|
default 32 if SYS_CACHE_SHIFT_5
|
||
|
|
|
||
|
|
config SYS_ARCH_TIMER
|
||
|
|
bool "ARM Generic Timer support"
|
||
|
|
depends on CPU_V7A || ARM64
|
||
|
|
default y if ARM64
|
||
|
|
help
|
||
|
|
The ARM Generic Timer (aka arch-timer) provides an architected
|
||
|
|
interface to a timer source on an SoC.
|
||
|
|
It is mandantory for ARMv8 implementation and widely available
|
||
|
|
on ARMv7 systems.
|
||
|
|
|
||
|
|
config ARM_SMCCC
|
||
|
|
bool "Support for ARM SMC Calling Convention (SMCCC)"
|
||
|
|
depends on CPU_V7A || ARM64
|
||
|
|
select ARM_PSCI_FW
|
||
|
|
help
|
||
|
|
Say Y here if you want to enable ARM SMC Calling Convention.
|
||
|
|
This should be enabled if U-Boot needs to communicate with system
|
||
|
|
firmware (for example, PSCI) according to SMCCC.
|
||
|
|
|
||
|
|
config SEMIHOSTING
|
||
|
|
bool "support boot from semihosting"
|
||
|
|
help
|
||
|
|
In emulated environments, semihosting is a way for
|
||
|
|
the hosted environment to call out to the emulator to
|
||
|
|
retrieve files from the host machine.
|
||
|
|
|
||
|
|
config SYS_THUMB_BUILD
|
||
|
|
bool "Build U-Boot using the Thumb instruction set"
|
||
|
|
depends on !ARM64
|
||
|
|
help
|
||
|
|
Use this flag to build U-Boot using the Thumb instruction set for
|
||
|
|
ARM architectures. Thumb instruction set provides better code
|
||
|
|
density. For ARM architectures that support Thumb2 this flag will
|
||
|
|
result in Thumb2 code generated by GCC.
|
||
|
|
|
||
|
|
config SPL_SYS_THUMB_BUILD
|
||
|
|
bool "Build SPL using the Thumb instruction set"
|
||
|
|
default y if SYS_THUMB_BUILD
|
||
|
|
depends on !ARM64
|
||
|
|
help
|
||
|
|
Use this flag to build SPL using the Thumb instruction set for
|
||
|
|
ARM architectures. Thumb instruction set provides better code
|
||
|
|
density. For ARM architectures that support Thumb2 this flag will
|
||
|
|
result in Thumb2 code generated by GCC.
|
||
|
|
|
||
|
|
config SYS_L2CACHE_OFF
|
||
|
|
bool "L2cache off"
|
||
|
|
help
|
||
|
|
If SoC does not support L2CACHE or one do not want to enable
|
||
|
|
L2CACHE, choose this option.
|
||
|
|
|
||
|
|
config ENABLE_ARM_SOC_BOOT0_HOOK
|
||
|
|
bool "prepare BOOT0 header"
|
||
|
|
help
|
||
|
|
If the SoC's BOOT0 requires a header area filled with (magic)
|
||
|
|
values, then choose this option, and create a file included as
|
||
|
|
<asm/arch/boot0.h> which contains the required assembler code.
|
||
|
|
|
||
|
|
config ARM_CORTEX_CPU_IS_UP
|
||
|
|
bool
|
||
|
|
default n
|
||
|
|
|
||
|
|
config USE_ARCH_MEMCPY
|
||
|
|
bool "Use an assembly optimized implementation of memcpy"
|
||
|
|
default y
|
||
|
|
depends on !ARM64
|
||
|
|
help
|
||
|
|
Enable the generation of an optimized version of memcpy.
|
||
|
|
Such implementation may be faster under some conditions
|
||
|
|
but may increase the binary size.
|
||
|
|
|
||
|
|
config SPL_USE_ARCH_MEMCPY
|
||
|
|
bool "Use an assembly optimized implementation of memcpy for SPL"
|
||
|
|
default y if USE_ARCH_MEMCPY
|
||
|
|
depends on !ARM64
|
||
|
|
help
|
||
|
|
Enable the generation of an optimized version of memcpy.
|
||
|
|
Such implementation may be faster under some conditions
|
||
|
|
but may increase the binary size.
|
||
|
|
|
||
|
|
config USE_ARCH_MEMSET
|
||
|
|
bool "Use an assembly optimized implementation of memset"
|
||
|
|
default y
|
||
|
|
depends on !ARM64
|
||
|
|
help
|
||
|
|
Enable the generation of an optimized version of memset.
|
||
|
|
Such implementation may be faster under some conditions
|
||
|
|
but may increase the binary size.
|
||
|
|
|
||
|
|
config SPL_USE_ARCH_MEMSET
|
||
|
|
bool "Use an assembly optimized implementation of memset for SPL"
|
||
|
|
default y if USE_ARCH_MEMSET
|
||
|
|
depends on !ARM64
|
||
|
|
help
|
||
|
|
Enable the generation of an optimized version of memset.
|
||
|
|
Such implementation may be faster under some conditions
|
||
|
|
but may increase the binary size.
|
||
|
|
|
||
|
|
config ARM64_SUPPORT_AARCH32
|
||
|
|
bool "ARM64 system support AArch32 execution state"
|
||
|
|
default y if ARM64 && !TARGET_THUNDERX_88XX
|
||
|
|
help
|
||
|
|
This ARM64 system supports AArch32 execution state.
|
||
|
|
|
||
|
|
choice
|
||
|
|
prompt "Target select"
|
||
|
|
default TARGET_HIKEY
|
||
|
|
|
||
|
|
config ARCH_AT91
|
||
|
|
bool "Atmel AT91"
|
||
|
|
select SPL_BOARD_INIT if SPL && !TARGET_SMARTWEB
|
||
|
|
|
||
|
|
config TARGET_EDB93XX
|
||
|
|
bool "Support edb93xx"
|
||
|
|
select CPU_ARM920T
|
||
|
|
select PL010_SERIAL
|
||
|
|
|
||
|
|
config TARGET_ASPENITE
|
||
|
|
bool "Support aspenite"
|
||
|
|
select CPU_ARM926EJS
|
||
|
|
|
||
|
|
config TARGET_GPLUGD
|
||
|
|
bool "Support gplugd"
|
||
|
|
select CPU_ARM926EJS
|
||
|
|
|
||
|
|
config ARCH_DAVINCI
|
||
|
|
bool "TI DaVinci"
|
||
|
|
select CPU_ARM926EJS
|
||
|
|
imply CMD_SAVES
|
||
|
|
help
|
||
|
|
Support for TI's DaVinci platform.
|
||
|
|
|
||
|
|
config KIRKWOOD
|
||
|
|
bool "Marvell Kirkwood"
|
||
|
|
select ARCH_MISC_INIT
|
||
|
|
select BOARD_EARLY_INIT_F
|
||
|
|
select CPU_ARM926EJS
|
||
|
|
|
||
|
|
config ARCH_MVEBU
|
||
|
|
bool "Marvell MVEBU family (Armada XP/375/38x/3700/7K/8K)"
|
||
|
|
select DM
|
||
|
|
select DM_ETH
|
||
|
|
select DM_SERIAL
|
||
|
|
select DM_SPI
|
||
|
|
select DM_SPI_FLASH
|
||
|
|
select OF_CONTROL
|
||
|
|
select OF_SEPARATE
|
||
|
|
select SPI
|
||
|
|
imply CMD_DM
|
||
|
|
|
||
|
|
config TARGET_APF27
|
||
|
|
bool "Support apf27"
|
||
|
|
select CPU_ARM926EJS
|
||
|
|
select SUPPORT_SPL
|
||
|
|
|
||
|
|
config ORION5X
|
||
|
|
bool "Marvell Orion"
|
||
|
|
select CPU_ARM926EJS
|
||
|
|
|
||
|
|
config TARGET_SPEAR300
|
||
|
|
bool "Support spear300"
|
||
|
|
select BOARD_EARLY_INIT_F
|
||
|
|
select CPU_ARM926EJS
|
||
|
|
select PL011_SERIAL
|
||
|
|
imply CMD_SAVES
|
||
|
|
|
||
|
|
config TARGET_SPEAR310
|
||
|
|
bool "Support spear310"
|
||
|
|
select BOARD_EARLY_INIT_F
|
||
|
|
select CPU_ARM926EJS
|
||
|
|
select PL011_SERIAL
|
||
|
|
imply CMD_SAVES
|
||
|
|
|
||
|
|
config TARGET_SPEAR320
|
||
|
|
bool "Support spear320"
|
||
|
|
select BOARD_EARLY_INIT_F
|
||
|
|
select CPU_ARM926EJS
|
||
|
|
select PL011_SERIAL
|
||
|
|
imply CMD_SAVES
|
||
|
|
|
||
|
|
config TARGET_SPEAR600
|
||
|
|
bool "Support spear600"
|
||
|
|
select BOARD_EARLY_INIT_F
|
||
|
|
select CPU_ARM926EJS
|
||
|
|
select PL011_SERIAL
|
||
|
|
imply CMD_SAVES
|
||
|
|
|
||
|
|
config TARGET_STV0991
|
||
|
|
bool "Support stv0991"
|
||
|
|
select CPU_V7A
|
||
|
|
select DM
|
||
|
|
select DM_SERIAL
|
||
|
|
select DM_SPI
|
||
|
|
select DM_SPI_FLASH
|
||
|
|
select PL01X_SERIAL
|
||
|
|
select SPI
|
||
|
|
select SPI_FLASH
|
||
|
|
imply CMD_DM
|
||
|
|
|
||
|
|
config TARGET_X600
|
||
|
|
bool "Support x600"
|
||
|
|
select BOARD_LATE_INIT
|
||
|
|
select CPU_ARM926EJS
|
||
|
|
select PL011_SERIAL
|
||
|
|
select SUPPORT_SPL
|
||
|
|
|
||
|
|
config TARGET_WOODBURN
|
||
|
|
bool "Support woodburn"
|
||
|
|
select CPU_ARM1136
|
||
|
|
|
||
|
|
config TARGET_WOODBURN_SD
|
||
|
|
bool "Support woodburn_sd"
|
||
|
|
select CPU_ARM1136
|
||
|
|
select SUPPORT_SPL
|
||
|
|
|
||
|
|
config TARGET_FLEA3
|
||
|
|
bool "Support flea3"
|
||
|
|
select CPU_ARM1136
|
||
|
|
|
||
|
|
config TARGET_MX35PDK
|
||
|
|
bool "Support mx35pdk"
|
||
|
|
select BOARD_LATE_INIT
|
||
|
|
select CPU_ARM1136
|
||
|
|
|
||
|
|
config ARCH_BCM283X
|
||
|
|
bool "Broadcom BCM283X family"
|
||
|
|
select DM
|
||
|
|
select DM_GPIO
|
||
|
|
select DM_SERIAL
|
||
|
|
select OF_CONTROL
|
||
|
|
select PL01X_SERIAL
|
||
|
|
select SERIAL_SEARCH_ALL
|
||
|
|
imply CMD_DM
|
||
|
|
imply FAT_WRITE
|
||
|
|
|
||
|
|
config ARCH_BCM6858
|
||
|
|
bool "Broadcom BCM6858 family"
|
||
|
|
select DM
|
||
|
|
select OF_CONTROL
|
||
|
|
imply CMD_DM
|
||
|
|
|
||
|
|
config TARGET_VEXPRESS_CA15_TC2
|
||
|
|
bool "Support vexpress_ca15_tc2"
|
||
|
|
select CPU_V7A
|
||
|
|
select CPU_V7_HAS_NONSEC
|
||
|
|
select CPU_V7_HAS_VIRT
|
||
|
|
select PL011_SERIAL
|
||
|
|
|
||
|
|
config ARCH_BCMSTB
|
||
|
|
bool "Broadcom BCM7XXX family"
|
||
|
|
select CPU_V7A
|
||
|
|
select DM
|
||
|
|
select OF_CONTROL
|
||
|
|
select OF_PRIOR_STAGE
|
||
|
|
imply CMD_DM
|
||
|
|
help
|
||
|
|
This enables support for Broadcom ARM-based set-top box
|
||
|
|
chipsets, including the 7445 family of chips.
|
||
|
|
|
||
|
|
config TARGET_VEXPRESS_CA5X2
|
||
|
|
bool "Support vexpress_ca5x2"
|
||
|
|
select CPU_V7A
|
||
|
|
select PL011_SERIAL
|
||
|
|
|
||
|
|
config TARGET_VEXPRESS_CA9X4
|
||
|
|
bool "Support vexpress_ca9x4"
|
||
|
|
select CPU_V7A
|
||
|
|
select PL011_SERIAL
|
||
|
|
|
||
|
|
config TARGET_BCM23550_W1D
|
||
|
|
bool "Support bcm23550_w1d"
|
||
|
|
select CPU_V7A
|
||
|
|
imply CRC32_VERIFY
|
||
|
|
imply FAT_WRITE
|
||
|
|
|
||
|
|
config TARGET_BCM28155_AP
|
||
|
|
bool "Support bcm28155_ap"
|
||
|
|
select CPU_V7A
|
||
|
|
imply CRC32_VERIFY
|
||
|
|
imply FAT_WRITE
|
||
|
|
|
||
|
|
config TARGET_BCMCYGNUS
|
||
|
|
bool "Support bcmcygnus"
|
||
|
|
select CPU_V7A
|
||
|
|
imply BCM_SF2_ETH
|
||
|
|
imply BCM_SF2_ETH_GMAC
|
||
|
|
imply CMD_HASH
|
||
|
|
imply CRC32_VERIFY
|
||
|
|
imply FAT_WRITE
|
||
|
|
imply HASH_VERIFY
|
||
|
|
imply NETDEVICES
|
||
|
|
|
||
|
|
config TARGET_BCMNSP
|
||
|
|
bool "Support bcmnsp"
|
||
|
|
select CPU_V7A
|
||
|
|
|
||
|
|
config TARGET_BCMNS2
|
||
|
|
bool "Support Broadcom Northstar2"
|
||
|
|
select ARM64
|
||
|
|
help
|
||
|
|
Support for Broadcom Northstar 2 SoCs. NS2 is a quad-core 64-bit
|
||
|
|
ARMv8 Cortex-A57 processors targeting a broad range of networking
|
||
|
|
applications
|
||
|
|
|
||
|
|
config ARCH_EXYNOS
|
||
|
|
bool "Samsung EXYNOS"
|
||
|
|
select DM
|
||
|
|
select DM_GPIO
|
||
|
|
select DM_I2C
|
||
|
|
select DM_KEYBOARD
|
||
|
|
select DM_SERIAL
|
||
|
|
select DM_SPI
|
||
|
|
select DM_SPI_FLASH
|
||
|
|
select SPI
|
||
|
|
imply SYS_THUMB_BUILD
|
||
|
|
imply CMD_DM
|
||
|
|
imply FAT_WRITE
|
||
|
|
|
||
|
|
config ARCH_S5PC1XX
|
||
|
|
bool "Samsung S5PC1XX"
|
||
|
|
select CPU_V7A
|
||
|
|
select DM
|
||
|
|
select DM_GPIO
|
||
|
|
select DM_I2C
|
||
|
|
select DM_SERIAL
|
||
|
|
imply CMD_DM
|
||
|
|
|
||
|
|
config ARCH_HIGHBANK
|
||
|
|
bool "Calxeda Highbank"
|
||
|
|
select CPU_V7A
|
||
|
|
select PL011_SERIAL
|
||
|
|
|
||
|
|
config ARCH_INTEGRATOR
|
||
|
|
bool "ARM Ltd. Integrator family"
|
||
|
|
select DM
|
||
|
|
select DM_SERIAL
|
||
|
|
select PL01X_SERIAL
|
||
|
|
imply CMD_DM
|
||
|
|
|
||
|
|
config ARCH_KEYSTONE
|
||
|
|
bool "TI Keystone"
|
||
|
|
select CMD_POWEROFF
|
||
|
|
select CPU_V7A
|
||
|
|
select SUPPORT_SPL
|
||
|
|
select SYS_ARCH_TIMER
|
||
|
|
select SYS_THUMB_BUILD
|
||
|
|
imply CMD_MTDPARTS
|
||
|
|
imply CMD_SAVES
|
||
|
|
imply FIT
|
||
|
|
|
||
|
|
config ARCH_K3
|
||
|
|
bool "Texas Instruments' K3 Architecture"
|
||
|
|
select SPL
|
||
|
|
select SUPPORT_SPL
|
||
|
|
select FIT
|
||
|
|
|
||
|
|
config ARCH_OMAP2PLUS
|
||
|
|
bool "TI OMAP2+"
|
||
|
|
select CPU_V7A
|
||
|
|
select SPL_BOARD_INIT if SPL
|
||
|
|
select SPL_STACK_R if SPL
|
||
|
|
select SUPPORT_SPL
|
||
|
|
imply FIT
|
||
|
|
|
||
|
|
config ARCH_MESON
|
||
|
|
bool "Amlogic Meson"
|
||
|
|
imply DISTRO_DEFAULTS
|
||
|
|
help
|
||
|
|
Support for the Meson SoC family developed by Amlogic Inc.,
|
||
|
|
targeted at media players and tablet computers. We currently
|
||
|
|
support the S905 (GXBaby) 64-bit SoC.
|
||
|
|
|
||
|
|
config ARCH_MEDIATEK
|
||
|
|
bool "MediaTek SoCs"
|
||
|
|
select BINMAN
|
||
|
|
select DM
|
||
|
|
select OF_CONTROL
|
||
|
|
select SPL_DM if SPL
|
||
|
|
select SPL_LIBCOMMON_SUPPORT if SPL
|
||
|
|
select SPL_LIBGENERIC_SUPPORT if SPL
|
||
|
|
select SPL_OF_CONTROL if SPL
|
||
|
|
select SUPPORT_SPL
|
||
|
|
help
|
||
|
|
Support for the MediaTek SoCs family developed by MediaTek Inc.
|
||
|
|
Please refer to doc/README.mediatek for more information.
|
||
|
|
|
||
|
|
config ARCH_LPC32XX
|
||
|
|
bool "NXP LPC32xx platform"
|
||
|
|
select CPU_ARM926EJS
|
||
|
|
select DM
|
||
|
|
select DM_GPIO
|
||
|
|
select DM_SERIAL
|
||
|
|
select SPL_DM if SPL
|
||
|
|
select SUPPORT_SPL
|
||
|
|
imply CMD_DM
|
||
|
|
|
||
|
|
config ARCH_IMX8
|
||
|
|
bool "NXP i.MX8 platform"
|
||
|
|
select ARM64
|
||
|
|
select DM
|
||
|
|
select OF_CONTROL
|
||
|
|
|
||
|
|
config ARCH_IMX8M
|
||
|
|
bool "NXP i.MX8M platform"
|
||
|
|
select ARM64
|
||
|
|
select DM
|
||
|
|
select SUPPORT_SPL
|
||
|
|
imply CMD_DM
|
||
|
|
|
||
|
|
config ARCH_MX23
|
||
|
|
bool "NXP i.MX23 family"
|
||
|
|
select CPU_ARM926EJS
|
||
|
|
select PL011_SERIAL
|
||
|
|
select SUPPORT_SPL
|
||
|
|
|
||
|
|
config ARCH_MX25
|
||
|
|
bool "NXP MX25"
|
||
|
|
select CPU_ARM926EJS
|
||
|
|
imply MXC_GPIO
|
||
|
|
|
||
|
|
config ARCH_MX28
|
||
|
|
bool "NXP i.MX28 family"
|
||
|
|
select CPU_ARM926EJS
|
||
|
|
select PL011_SERIAL
|
||
|
|
select SUPPORT_SPL
|
||
|
|
|
||
|
|
config ARCH_MX31
|
||
|
|
bool "NXP i.MX31 family"
|
||
|
|
select CPU_ARM1136
|
||
|
|
|
||
|
|
config ARCH_MX7ULP
|
||
|
|
bool "NXP MX7ULP"
|
||
|
|
select CPU_V7A
|
||
|
|
select ROM_UNIFIED_SECTIONS
|
||
|
|
imply MXC_GPIO
|
||
|
|
|
||
|
|
config ARCH_MX7
|
||
|
|
bool "Freescale MX7"
|
||
|
|
select ARCH_MISC_INIT
|
||
|
|
select BOARD_EARLY_INIT_F
|
||
|
|
select CPU_V7A
|
||
|
|
select SYS_FSL_HAS_SEC if SECURE_BOOT
|
||
|
|
select SYS_FSL_SEC_COMPAT_4
|
||
|
|
select SYS_FSL_SEC_LE
|
||
|
|
imply MXC_GPIO
|
||
|
|
|
||
|
|
config ARCH_MX6
|
||
|
|
bool "Freescale MX6"
|
||
|
|
select CPU_V7A
|
||
|
|
select SYS_FSL_HAS_SEC if SECURE_BOOT
|
||
|
|
select SYS_FSL_SEC_COMPAT_4
|
||
|
|
select SYS_FSL_SEC_LE
|
||
|
|
select SYS_THUMB_BUILD if SPL
|
||
|
|
imply MXC_GPIO
|
||
|
|
|
||
|
|
if ARCH_MX6
|
||
|
|
config SPL_LDSCRIPT
|
||
|
|
default "arch/arm/mach-omap2/u-boot-spl.lds"
|
||
|
|
endif
|
||
|
|
|
||
|
|
config ARCH_MX5
|
||
|
|
bool "Freescale MX5"
|
||
|
|
select BOARD_EARLY_INIT_F
|
||
|
|
select CPU_V7A
|
||
|
|
imply MXC_GPIO
|
||
|
|
|
||
|
|
config ARCH_OWL
|
||
|
|
bool "Actions Semi OWL SoCs"
|
||
|
|
select ARM64
|
||
|
|
select DM
|
||
|
|
select DM_SERIAL
|
||
|
|
select OF_CONTROL
|
||
|
|
imply CMD_DM
|
||
|
|
|
||
|
|
config ARCH_QEMU
|
||
|
|
bool "QEMU Virtual Platform"
|
||
|
|
select DM
|
||
|
|
select DM_SERIAL
|
||
|
|
select OF_CONTROL
|
||
|
|
select PL01X_SERIAL
|
||
|
|
imply CMD_DM
|
||
|
|
imply DM_RTC
|
||
|
|
imply RTC_PL031
|
||
|
|
|
||
|
|
config ARCH_RMOBILE
|
||
|
|
bool "Renesas ARM SoCs"
|
||
|
|
select BOARD_EARLY_INIT_F
|
||
|
|
select DM
|
||
|
|
select DM_SERIAL
|
||
|
|
imply CMD_DM
|
||
|
|
imply FAT_WRITE
|
||
|
|
imply SYS_THUMB_BUILD
|
||
|
|
imply ARCH_MISC_INIT if DISPLAY_CPUINFO
|
||
|
|
|
||
|
|
config TARGET_S32V234EVB
|
||
|
|
bool "Support s32v234evb"
|
||
|
|
select ARM64
|
||
|
|
select SYS_FSL_ERRATUM_ESDHC111
|
||
|
|
|
||
|
|
config ARCH_SNAPDRAGON
|
||
|
|
bool "Qualcomm Snapdragon SoCs"
|
||
|
|
select ARM64
|
||
|
|
select DM
|
||
|
|
select DM_GPIO
|
||
|
|
select DM_SERIAL
|
||
|
|
select MSM_SMEM
|
||
|
|
select OF_CONTROL
|
||
|
|
select OF_SEPARATE
|
||
|
|
select SMEM
|
||
|
|
select SPMI
|
||
|
|
imply CMD_DM
|
||
|
|
|
||
|
|
config ARCH_SOCFPGA
|
||
|
|
bool "Altera SOCFPGA family"
|
||
|
|
select ARCH_EARLY_INIT_R
|
||
|
|
select ARCH_MISC_INIT if !TARGET_SOCFPGA_ARRIA10
|
||
|
|
select ARM64 if TARGET_SOCFPGA_STRATIX10
|
||
|
|
select CPU_V7A if TARGET_SOCFPGA_GEN5 || TARGET_SOCFPGA_ARRIA10
|
||
|
|
select DM
|
||
|
|
select DM_SERIAL
|
||
|
|
select ENABLE_ARM_SOC_BOOT0_HOOK if TARGET_SOCFPGA_GEN5 || TARGET_SOCFPGA_ARRIA10
|
||
|
|
select OF_CONTROL
|
||
|
|
select SPL_DM_RESET if DM_RESET
|
||
|
|
select SPL_DM_SERIAL
|
||
|
|
select SPL_LIBCOMMON_SUPPORT
|
||
|
|
select SPL_LIBGENERIC_SUPPORT
|
||
|
|
select SPL_NAND_SUPPORT if SPL_NAND_DENALI
|
||
|
|
select SPL_OF_CONTROL
|
||
|
|
select SPL_SEPARATE_BSS if TARGET_SOCFPGA_STRATIX10
|
||
|
|
select SPL_SERIAL_SUPPORT
|
||
|
|
select SPL_WATCHDOG_SUPPORT
|
||
|
|
select SUPPORT_SPL
|
||
|
|
select SYS_NS16550
|
||
|
|
select SYS_THUMB_BUILD if TARGET_SOCFPGA_GEN5 || TARGET_SOCFPGA_ARRIA10
|
||
|
|
imply CMD_DM
|
||
|
|
imply CMD_MTDPARTS
|
||
|
|
imply CRC32_VERIFY
|
||
|
|
imply DM_SPI
|
||
|
|
imply DM_SPI_FLASH
|
||
|
|
imply FAT_WRITE
|
||
|
|
imply SPL_LIBDISK_SUPPORT
|
||
|
|
imply SPL_MMC_SUPPORT
|
||
|
|
imply SYS_MMCSD_RAW_MODE_U_BOOT_USE_PARTITION
|
||
|
|
imply SYS_MMCSD_RAW_MODE_U_BOOT_USE_PARTITION_TYPE
|
||
|
|
imply SPL_SPI_FLASH_SUPPORT
|
||
|
|
imply SPL_SPI_SUPPORT
|
||
|
|
|
||
|
|
config ARCH_SUNXI
|
||
|
|
bool "Support sunxi (Allwinner) SoCs"
|
||
|
|
select BINMAN
|
||
|
|
select CMD_GPIO
|
||
|
|
select CMD_MMC if MMC
|
||
|
|
select CMD_USB if DISTRO_DEFAULTS
|
||
|
|
select DM
|
||
|
|
select DM_ETH
|
||
|
|
select DM_GPIO
|
||
|
|
select DM_KEYBOARD
|
||
|
|
select DM_SERIAL
|
||
|
|
select DM_USB if DISTRO_DEFAULTS
|
||
|
|
select OF_BOARD_SETUP
|
||
|
|
select OF_CONTROL
|
||
|
|
select OF_SEPARATE
|
||
|
|
select SPECIFY_CONSOLE_INDEX
|
||
|
|
select SPL_STACK_R if SPL
|
||
|
|
select SPL_SYS_MALLOC_SIMPLE if SPL
|
||
|
|
select SPL_SYS_THUMB_BUILD if !ARM64
|
||
|
|
select SYS_NS16550
|
||
|
|
select SYS_THUMB_BUILD if !ARM64
|
||
|
|
select USB if DISTRO_DEFAULTS
|
||
|
|
select USB_KEYBOARD if DISTRO_DEFAULTS
|
||
|
|
select USB_STORAGE if DISTRO_DEFAULTS
|
||
|
|
select USE_TINY_PRINTF
|
||
|
|
imply CMD_DM
|
||
|
|
imply CMD_GPT
|
||
|
|
imply CMD_UBI if NAND
|
||
|
|
imply DISTRO_DEFAULTS
|
||
|
|
imply FAT_WRITE
|
||
|
|
imply FIT
|
||
|
|
imply OF_LIBFDT_OVERLAY
|
||
|
|
imply PRE_CONSOLE_BUFFER
|
||
|
|
imply SPL_GPIO_SUPPORT
|
||
|
|
imply SPL_LIBCOMMON_SUPPORT
|
||
|
|
imply SPL_LIBGENERIC_SUPPORT
|
||
|
|
imply SPL_MMC_SUPPORT if MMC
|
||
|
|
imply SPL_POWER_SUPPORT
|
||
|
|
imply SPL_SERIAL_SUPPORT
|
||
|
|
imply USB_GADGET
|
||
|
|
|
||
|
|
config ARCH_VERSAL
|
||
|
|
bool "Support Xilinx Versal Platform"
|
||
|
|
select ARM64
|
||
|
|
select CLK
|
||
|
|
select DM
|
||
|
|
select DM_SERIAL
|
||
|
|
select OF_CONTROL
|
||
|
|
|
||
|
|
config ARCH_VF610
|
||
|
|
bool "Freescale Vybrid"
|
||
|
|
select CPU_V7A
|
||
|
|
select SYS_FSL_ERRATUM_ESDHC111
|
||
|
|
imply CMD_MTDPARTS
|
||
|
|
imply NAND
|
||
|
|
|
||
|
|
config ARCH_ZYNQ
|
||
|
|
bool "Xilinx Zynq based platform"
|
||
|
|
select BOARD_EARLY_INIT_F if WDT
|
||
|
|
select CLK
|
||
|
|
select CLK_ZYNQ
|
||
|
|
select CPU_V7A
|
||
|
|
select DM
|
||
|
|
select DM_ETH if NET
|
||
|
|
select DM_MMC if MMC
|
||
|
|
select DM_SERIAL
|
||
|
|
select DM_SPI
|
||
|
|
select DM_SPI_FLASH
|
||
|
|
select DM_USB if USB
|
||
|
|
select OF_CONTROL
|
||
|
|
select SPI
|
||
|
|
select SPL_BOARD_INIT if SPL
|
||
|
|
select SPL_CLK if SPL
|
||
|
|
select SPL_DM if SPL
|
||
|
|
select SPL_OF_CONTROL if SPL
|
||
|
|
select SPL_SEPARATE_BSS if SPL
|
||
|
|
select SUPPORT_SPL
|
||
|
|
imply ARCH_EARLY_INIT_R
|
||
|
|
imply BOARD_LATE_INIT
|
||
|
|
imply CMD_CLK
|
||
|
|
imply CMD_DM
|
||
|
|
imply CMD_SPL
|
||
|
|
imply FAT_WRITE
|
||
|
|
|
||
|
|
config ARCH_ZYNQMP_R5
|
||
|
|
bool "Xilinx ZynqMP R5 based platform"
|
||
|
|
select CLK
|
||
|
|
select CPU_V7R
|
||
|
|
select DM
|
||
|
|
select DM_SERIAL
|
||
|
|
select OF_CONTROL
|
||
|
|
imply CMD_DM
|
||
|
|
imply DM_USB_GADGET
|
||
|
|
|
||
|
|
config ARCH_ZYNQMP
|
||
|
|
bool "Xilinx ZynqMP based platform"
|
||
|
|
select ARM64
|
||
|
|
select CLK
|
||
|
|
select DM
|
||
|
|
select DM_SERIAL
|
||
|
|
select DM_USB if USB
|
||
|
|
select OF_CONTROL
|
||
|
|
select SPL_BOARD_INIT if SPL
|
||
|
|
select SPL_CLK if SPL
|
||
|
|
select SPL_SEPARATE_BSS if SPL
|
||
|
|
select SUPPORT_SPL
|
||
|
|
imply BOARD_LATE_INIT
|
||
|
|
imply CMD_DM
|
||
|
|
imply FAT_WRITE
|
||
|
|
imply MP
|
||
|
|
imply DM_USB_GADGET
|
||
|
|
|
||
|
|
config TEGRA
|
||
|
|
bool "NVIDIA Tegra"
|
||
|
|
imply DISTRO_DEFAULTS
|
||
|
|
imply FAT_WRITE
|
||
|
|
|
||
|
|
config TARGET_VEXPRESS64_AEMV8A
|
||
|
|
bool "Support vexpress_aemv8a"
|
||
|
|
select ARM64
|
||
|
|
select PL01X_SERIAL
|
||
|
|
|
||
|
|
config TARGET_VEXPRESS64_BASE_FVP
|
||
|
|
bool "Support Versatile Express ARMv8a FVP BASE model"
|
||
|
|
select ARM64
|
||
|
|
select PL01X_SERIAL
|
||
|
|
select SEMIHOSTING
|
||
|
|
|
||
|
|
config TARGET_VEXPRESS64_BASE_FVP_DRAM
|
||
|
|
bool "Support Versatile Express ARMv8a FVP BASE model booting from DRAM"
|
||
|
|
select ARM64
|
||
|
|
select PL01X_SERIAL
|
||
|
|
help
|
||
|
|
This target is derived from TARGET_VEXPRESS64_BASE_FVP and over-rides
|
||
|
|
the default config to allow the user to load the images directly into
|
||
|
|
DRAM using model parameters rather than by using semi-hosting to load
|
||
|
|
the files from the host filesystem.
|
||
|
|
|
||
|
|
config TARGET_VEXPRESS64_JUNO
|
||
|
|
bool "Support Versatile Express Juno Development Platform"
|
||
|
|
select ARM64
|
||
|
|
select PL01X_SERIAL
|
||
|
|
|
||
|
|
config TARGET_LS2080A_EMU
|
||
|
|
bool "Support ls2080a_emu"
|
||
|
|
select ARCH_LS2080A
|
||
|
|
select ARCH_MISC_INIT
|
||
|
|
select ARM64
|
||
|
|
select ARMV8_MULTIENTRY
|
||
|
|
help
|
||
|
|
Support for Freescale LS2080A_EMU platform
|
||
|
|
The LS2080A Development System (EMULATOR) is a pre silicon
|
||
|
|
development platform that supports the QorIQ LS2080A
|
||
|
|
Layerscape Architecture processor.
|
||
|
|
|
||
|
|
config TARGET_LS2080A_SIMU
|
||
|
|
bool "Support ls2080a_simu"
|
||
|
|
select ARCH_LS2080A
|
||
|
|
select ARCH_MISC_INIT
|
||
|
|
select ARM64
|
||
|
|
select ARMV8_MULTIENTRY
|
||
|
|
help
|
||
|
|
Support for Freescale LS2080A_SIMU platform
|
||
|
|
The LS2080A Development System (QDS) is a pre silicon
|
||
|
|
development platform that supports the QorIQ LS2080A
|
||
|
|
Layerscape Architecture processor.
|
||
|
|
|
||
|
|
config TARGET_LS1088AQDS
|
||
|
|
bool "Support ls1088aqds"
|
||
|
|
select ARCH_LS1088A
|
||
|
|
select ARCH_MISC_INIT
|
||
|
|
select ARM64
|
||
|
|
select ARMV8_MULTIENTRY
|
||
|
|
select BOARD_LATE_INIT
|
||
|
|
select SUPPORT_SPL
|
||
|
|
help
|
||
|
|
Support for NXP LS1088AQDS platform
|
||
|
|
The LS1088A Development System (QDS) is a high-performance
|
||
|
|
development platform that supports the QorIQ LS1088A
|
||
|
|
Layerscape Architecture processor.
|
||
|
|
|
||
|
|
config TARGET_LS2080AQDS
|
||
|
|
bool "Support ls2080aqds"
|
||
|
|
select ARCH_LS2080A
|
||
|
|
select ARCH_MISC_INIT
|
||
|
|
select ARM64
|
||
|
|
select ARMV8_MULTIENTRY
|
||
|
|
select BOARD_LATE_INIT
|
||
|
|
select SUPPORT_SPL
|
||
|
|
imply SCSI
|
||
|
|
imply SCSI_AHCI
|
||
|
|
help
|
||
|
|
Support for Freescale LS2080AQDS platform
|
||
|
|
The LS2080A Development System (QDS) is a high-performance
|
||
|
|
development platform that supports the QorIQ LS2080A
|
||
|
|
Layerscape Architecture processor.
|
||
|
|
|
||
|
|
config TARGET_LS2080ARDB
|
||
|
|
bool "Support ls2080ardb"
|
||
|
|
select ARCH_LS2080A
|
||
|
|
select ARCH_MISC_INIT
|
||
|
|
select ARM64
|
||
|
|
select ARMV8_MULTIENTRY
|
||
|
|
select BOARD_LATE_INIT
|
||
|
|
select SUPPORT_SPL
|
||
|
|
imply SCSI
|
||
|
|
imply SCSI_AHCI
|
||
|
|
help
|
||
|
|
Support for Freescale LS2080ARDB platform.
|
||
|
|
The LS2080A Reference design board (RDB) is a high-performance
|
||
|
|
development platform that supports the QorIQ LS2080A
|
||
|
|
Layerscape Architecture processor.
|
||
|
|
|
||
|
|
config TARGET_LS2081ARDB
|
||
|
|
bool "Support ls2081ardb"
|
||
|
|
select ARCH_LS2080A
|
||
|
|
select ARCH_MISC_INIT
|
||
|
|
select ARM64
|
||
|
|
select ARMV8_MULTIENTRY
|
||
|
|
select BOARD_LATE_INIT
|
||
|
|
select SUPPORT_SPL
|
||
|
|
help
|
||
|
|
Support for Freescale LS2081ARDB platform.
|
||
|
|
The LS2081A Reference design board (RDB) is a high-performance
|
||
|
|
development platform that supports the QorIQ LS2081A/LS2041A
|
||
|
|
Layerscape Architecture processor.
|
||
|
|
|
||
|
|
config TARGET_HIKEY
|
||
|
|
bool "Support HiKey 96boards Consumer Edition Platform"
|
||
|
|
select ARM64
|
||
|
|
select DM
|
||
|
|
select DM_GPIO
|
||
|
|
select DM_SERIAL
|
||
|
|
select OF_CONTROL
|
||
|
|
select PL01X_SERIAL
|
||
|
|
select SPECIFY_CONSOLE_INDEX
|
||
|
|
imply CMD_DM
|
||
|
|
help
|
||
|
|
Support for HiKey 96boards platform. It features a HI6220
|
||
|
|
SoC, with 8xA53 CPU, mali450 gpu, and 1GB RAM.
|
||
|
|
|
||
|
|
config TARGET_POPLAR
|
||
|
|
bool "Support Poplar 96boards Enterprise Edition Platform"
|
||
|
|
select ARM64
|
||
|
|
select DM
|
||
|
|
select DM_SERIAL
|
||
|
|
select DM_USB
|
||
|
|
select OF_CONTROL
|
||
|
|
select PL01X_SERIAL
|
||
|
|
imply CMD_DM
|
||
|
|
help
|
||
|
|
Support for Poplar 96boards EE platform. It features a HI3798cv200
|
||
|
|
SoC, with 4xA53 CPU, 1GB RAM and the high performance Mali T720 GPU
|
||
|
|
making it capable of running any commercial set-top solution based on
|
||
|
|
Linux or Android.
|
||
|
|
|
||
|
|
config TARGET_LS1012AQDS
|
||
|
|
bool "Support ls1012aqds"
|
||
|
|
select ARCH_LS1012A
|
||
|
|
select ARM64
|
||
|
|
select BOARD_LATE_INIT
|
||
|
|
help
|
||
|
|
Support for Freescale LS1012AQDS platform.
|
||
|
|
The LS1012A Development System (QDS) is a high-performance
|
||
|
|
development platform that supports the QorIQ LS1012A
|
||
|
|
Layerscape Architecture processor.
|
||
|
|
|
||
|
|
config TARGET_LS1012ARDB
|
||
|
|
bool "Support ls1012ardb"
|
||
|
|
select ARCH_LS1012A
|
||
|
|
select ARM64
|
||
|
|
select BOARD_LATE_INIT
|
||
|
|
imply SCSI
|
||
|
|
imply SCSI_AHCI
|
||
|
|
help
|
||
|
|
Support for Freescale LS1012ARDB platform.
|
||
|
|
The LS1012A Reference design board (RDB) is a high-performance
|
||
|
|
development platform that supports the QorIQ LS1012A
|
||
|
|
Layerscape Architecture processor.
|
||
|
|
|
||
|
|
config TARGET_LS1012A2G5RDB
|
||
|
|
bool "Support ls1012a2g5rdb"
|
||
|
|
select ARCH_LS1012A
|
||
|
|
select ARM64
|
||
|
|
select BOARD_LATE_INIT
|
||
|
|
imply SCSI
|
||
|
|
help
|
||
|
|
Support for Freescale LS1012A2G5RDB platform.
|
||
|
|
The LS1012A 2G5 Reference design board (RDB) is a high-performance
|
||
|
|
development platform that supports the QorIQ LS1012A
|
||
|
|
Layerscape Architecture processor.
|
||
|
|
|
||
|
|
config TARGET_LS1012AFRWY
|
||
|
|
bool "Support ls1012afrwy"
|
||
|
|
select ARCH_LS1012A
|
||
|
|
select ARM64
|
||
|
|
select BOARD_LATE_INIT
|
||
|
|
imply SCSI
|
||
|
|
imply SCSI_AHCI
|
||
|
|
help
|
||
|
|
Support for Freescale LS1012AFRWY platform.
|
||
|
|
The LS1012A FRWY board (FRWY) is a high-performance
|
||
|
|
development platform that supports the QorIQ LS1012A
|
||
|
|
Layerscape Architecture processor.
|
||
|
|
|
||
|
|
config TARGET_LS1012AFRDM
|
||
|
|
bool "Support ls1012afrdm"
|
||
|
|
select ARCH_LS1012A
|
||
|
|
select ARM64
|
||
|
|
help
|
||
|
|
Support for Freescale LS1012AFRDM platform.
|
||
|
|
The LS1012A Freedom board (FRDM) is a high-performance
|
||
|
|
development platform that supports the QorIQ LS1012A
|
||
|
|
Layerscape Architecture processor.
|
||
|
|
|
||
|
|
config TARGET_LS1088ARDB
|
||
|
|
bool "Support ls1088ardb"
|
||
|
|
select ARCH_LS1088A
|
||
|
|
select ARCH_MISC_INIT
|
||
|
|
select ARM64
|
||
|
|
select ARMV8_MULTIENTRY
|
||
|
|
select BOARD_LATE_INIT
|
||
|
|
select SUPPORT_SPL
|
||
|
|
help
|
||
|
|
Support for NXP LS1088ARDB platform.
|
||
|
|
The LS1088A Reference design board (RDB) is a high-performance
|
||
|
|
development platform that supports the QorIQ LS1088A
|
||
|
|
Layerscape Architecture processor.
|
||
|
|
|
||
|
|
config TARGET_LS1021AQDS
|
||
|
|
bool "Support ls1021aqds"
|
||
|
|
select ARCH_LS1021A
|
||
|
|
select ARCH_SUPPORT_PSCI
|
||
|
|
select BOARD_EARLY_INIT_F
|
||
|
|
select BOARD_LATE_INIT
|
||
|
|
select CPU_V7A
|
||
|
|
select CPU_V7_HAS_NONSEC
|
||
|
|
select CPU_V7_HAS_VIRT
|
||
|
|
select LS1_DEEP_SLEEP
|
||
|
|
select SUPPORT_SPL
|
||
|
|
select SYS_FSL_DDR
|
||
|
|
imply SCSI
|
||
|
|
|
||
|
|
config TARGET_LS1021ATWR
|
||
|
|
bool "Support ls1021atwr"
|
||
|
|
select ARCH_LS1021A
|
||
|
|
select ARCH_SUPPORT_PSCI
|
||
|
|
select BOARD_EARLY_INIT_F
|
||
|
|
select BOARD_LATE_INIT
|
||
|
|
select CPU_V7A
|
||
|
|
select CPU_V7_HAS_NONSEC
|
||
|
|
select CPU_V7_HAS_VIRT
|
||
|
|
select LS1_DEEP_SLEEP
|
||
|
|
select SUPPORT_SPL
|
||
|
|
imply SCSI
|
||
|
|
|
||
|
|
config TARGET_LS1021AIOT
|
||
|
|
bool "Support ls1021aiot"
|
||
|
|
select ARCH_LS1021A
|
||
|
|
select ARCH_SUPPORT_PSCI
|
||
|
|
select BOARD_LATE_INIT
|
||
|
|
select CPU_V7A
|
||
|
|
select CPU_V7_HAS_NONSEC
|
||
|
|
select CPU_V7_HAS_VIRT
|
||
|
|
select SUPPORT_SPL
|
||
|
|
imply SCSI
|
||
|
|
help
|
||
|
|
Support for Freescale LS1021AIOT platform.
|
||
|
|
The LS1021A Freescale board (IOT) is a high-performance
|
||
|
|
development platform that supports the QorIQ LS1021A
|
||
|
|
Layerscape Architecture processor.
|
||
|
|
|
||
|
|
config TARGET_LS1043AQDS
|
||
|
|
bool "Support ls1043aqds"
|
||
|
|
select ARCH_LS1043A
|
||
|
|
select ARM64
|
||
|
|
select ARMV8_MULTIENTRY
|
||
|
|
select BOARD_EARLY_INIT_F
|
||
|
|
select BOARD_LATE_INIT
|
||
|
|
select SUPPORT_SPL
|
||
|
|
imply SCSI
|
||
|
|
help
|
||
|
|
Support for Freescale LS1043AQDS platform.
|
||
|
|
|
||
|
|
config TARGET_LS1043ARDB
|
||
|
|
bool "Support ls1043ardb"
|
||
|
|
select ARCH_LS1043A
|
||
|
|
select ARM64
|
||
|
|
select ARMV8_MULTIENTRY
|
||
|
|
select BOARD_EARLY_INIT_F
|
||
|
|
select BOARD_LATE_INIT
|
||
|
|
select SUPPORT_SPL
|
||
|
|
imply SCSI
|
||
|
|
help
|
||
|
|
Support for Freescale LS1043ARDB platform.
|
||
|
|
|
||
|
|
config TARGET_LS1046AQDS
|
||
|
|
bool "Support ls1046aqds"
|
||
|
|
select ARCH_LS1046A
|
||
|
|
select ARM64
|
||
|
|
select ARMV8_MULTIENTRY
|
||
|
|
select BOARD_EARLY_INIT_F
|
||
|
|
select BOARD_LATE_INIT
|
||
|
|
select DM_SPI_FLASH if DM_SPI
|
||
|
|
select SUPPORT_SPL
|
||
|
|
imply SCSI
|
||
|
|
help
|
||
|
|
Support for Freescale LS1046AQDS platform.
|
||
|
|
The LS1046A Development System (QDS) is a high-performance
|
||
|
|
development platform that supports the QorIQ LS1046A
|
||
|
|
Layerscape Architecture processor.
|
||
|
|
|
||
|
|
config TARGET_LS1046ARDB
|
||
|
|
bool "Support ls1046ardb"
|
||
|
|
select ARCH_LS1046A
|
||
|
|
select ARM64
|
||
|
|
select ARMV8_MULTIENTRY
|
||
|
|
select BOARD_EARLY_INIT_F
|
||
|
|
select BOARD_LATE_INIT
|
||
|
|
select DM_SPI_FLASH if DM_SPI
|
||
|
|
select POWER_MC34VR500
|
||
|
|
select SUPPORT_SPL
|
||
|
|
imply SCSI
|
||
|
|
help
|
||
|
|
Support for Freescale LS1046ARDB platform.
|
||
|
|
The LS1046A Reference Design Board (RDB) is a high-performance
|
||
|
|
development platform that supports the QorIQ LS1046A
|
||
|
|
Layerscape Architecture processor.
|
||
|
|
|
||
|
|
config TARGET_H2200
|
||
|
|
bool "Support h2200"
|
||
|
|
select CPU_PXA
|
||
|
|
|
||
|
|
config TARGET_ZIPITZ2
|
||
|
|
bool "Support zipitz2"
|
||
|
|
select CPU_PXA
|
||
|
|
|
||
|
|
config TARGET_COLIBRI_PXA270
|
||
|
|
bool "Support colibri_pxa270"
|
||
|
|
select CPU_PXA
|
||
|
|
|
||
|
|
config ARCH_UNIPHIER
|
||
|
|
bool "Socionext UniPhier SoCs"
|
||
|
|
select BOARD_LATE_INIT
|
||
|
|
select DM
|
||
|
|
select DM_GPIO
|
||
|
|
select DM_I2C
|
||
|
|
select DM_MMC
|
||
|
|
select DM_RESET
|
||
|
|
select DM_SERIAL
|
||
|
|
select DM_USB
|
||
|
|
select OF_BOARD_SETUP
|
||
|
|
select OF_CONTROL
|
||
|
|
select OF_LIBFDT
|
||
|
|
select PINCTRL
|
||
|
|
select SPL_BOARD_INIT if SPL
|
||
|
|
select SPL_DM if SPL
|
||
|
|
select SPL_LIBCOMMON_SUPPORT if SPL
|
||
|
|
select SPL_LIBGENERIC_SUPPORT if SPL
|
||
|
|
select SPL_OF_CONTROL if SPL
|
||
|
|
select SPL_PINCTRL if SPL
|
||
|
|
select SUPPORT_SPL
|
||
|
|
imply CMD_DM
|
||
|
|
imply DISTRO_DEFAULTS
|
||
|
|
imply FAT_WRITE
|
||
|
|
help
|
||
|
|
Support for UniPhier SoC family developed by Socionext Inc.
|
||
|
|
(formerly, System LSI Business Division of Panasonic Corporation)
|
||
|
|
|
||
|
|
config STM32
|
||
|
|
bool "Support STMicroelectronics STM32 MCU with cortex M"
|
||
|
|
select CPU_V7M
|
||
|
|
select DM
|
||
|
|
select DM_SERIAL
|
||
|
|
imply CMD_DM
|
||
|
|
|
||
|
|
config ARCH_STI
|
||
|
|
bool "Support STMicrolectronics SoCs"
|
||
|
|
select BLK
|
||
|
|
select CPU_V7A
|
||
|
|
select DM
|
||
|
|
select DM_MMC
|
||
|
|
select DM_RESET
|
||
|
|
select DM_SERIAL
|
||
|
|
imply CMD_DM
|
||
|
|
help
|
||
|
|
Support for STMicroelectronics STiH407/10 SoC family.
|
||
|
|
This SoC is used on Linaro 96Board STiH410-B2260
|
||
|
|
|
||
|
|
config ARCH_STM32MP
|
||
|
|
bool "Support STMicroelectronics STM32MP Socs with cortex A"
|
||
|
|
select ARCH_MISC_INIT
|
||
|
|
select BOARD_LATE_INIT
|
||
|
|
select CLK
|
||
|
|
select DM
|
||
|
|
select DM_GPIO
|
||
|
|
select DM_RESET
|
||
|
|
select DM_SERIAL
|
||
|
|
select MISC
|
||
|
|
select OF_CONTROL
|
||
|
|
select OF_LIBFDT
|
||
|
|
select PINCTRL
|
||
|
|
select REGMAP
|
||
|
|
select SUPPORT_SPL
|
||
|
|
select SYSCON
|
||
|
|
select SYSRESET
|
||
|
|
select SYS_THUMB_BUILD
|
||
|
|
imply CMD_DM
|
||
|
|
help
|
||
|
|
Support for STM32MP SoC family developed by STMicroelectronics,
|
||
|
|
MPUs based on ARM cortex A core
|
||
|
|
U-BOOT is running in DDR and SPL support is the unsecure First Stage
|
||
|
|
BootLoader (FSBL)
|
||
|
|
|
||
|
|
config ARCH_ROCKCHIP
|
||
|
|
bool "Support Rockchip SoCs"
|
||
|
|
select BLK
|
||
|
|
select DM
|
||
|
|
select DM_GPIO
|
||
|
|
select DM_I2C
|
||
|
|
select DM_MMC
|
||
|
|
select DM_PWM
|
||
|
|
select DM_REGULATOR
|
||
|
|
select DM_SERIAL
|
||
|
|
select DM_SPI
|
||
|
|
select DM_SPI_FLASH
|
||
|
|
select DM_USB if USB
|
||
|
|
select ENABLE_ARM_SOC_BOOT0_HOOK
|
||
|
|
select OF_CONTROL
|
||
|
|
select SPI
|
||
|
|
select SPL_DM if SPL
|
||
|
|
select SPL_SYS_MALLOC_SIMPLE if SPL
|
||
|
|
select SYS_MALLOC_F
|
||
|
|
select SYS_THUMB_BUILD if !ARM64
|
||
|
|
imply ADC
|
||
|
|
imply CMD_DM
|
||
|
|
imply DISTRO_DEFAULTS
|
||
|
|
imply FAT_WRITE
|
||
|
|
imply SARADC_ROCKCHIP
|
||
|
|
imply SPL_SYSRESET
|
||
|
|
imply SYS_NS16550
|
||
|
|
imply TPL_SYSRESET
|
||
|
|
imply USB_FUNCTION_FASTBOOT
|
||
|
|
|
||
|
|
config TARGET_THUNDERX_88XX
|
||
|
|
bool "Support ThunderX 88xx"
|
||
|
|
select ARM64
|
||
|
|
select OF_CONTROL
|
||
|
|
select PL01X_SERIAL
|
||
|
|
select SYS_CACHE_SHIFT_7
|
||
|
|
|
||
|
|
config ARCH_ASPEED
|
||
|
|
bool "Support Aspeed SoCs"
|
||
|
|
select DM
|
||
|
|
select OF_CONTROL
|
||
|
|
imply CMD_DM
|
||
|
|
|
||
|
|
endchoice
|
||
|
|
|
||
|
|
config TI_SECURE_DEVICE
|
||
|
|
bool "HS Device Type Support"
|
||
|
|
depends on ARCH_KEYSTONE || ARCH_OMAP2PLUS
|
||
|
|
help
|
||
|
|
If a high secure (HS) device type is being used, this config
|
||
|
|
must be set. This option impacts various aspects of the
|
||
|
|
build system (to create signed boot images that can be
|
||
|
|
authenticated) and the code. See the doc/README.ti-secure
|
||
|
|
file for further details.
|
||
|
|
|
||
|
|
source "arch/arm/mach-aspeed/Kconfig"
|
||
|
|
|
||
|
|
source "arch/arm/mach-at91/Kconfig"
|
||
|
|
|
||
|
|
source "arch/arm/mach-bcm283x/Kconfig"
|
||
|
|
|
||
|
|
source "arch/arm/mach-bcmstb/Kconfig"
|
||
|
|
|
||
|
|
source "arch/arm/mach-davinci/Kconfig"
|
||
|
|
|
||
|
|
source "arch/arm/mach-exynos/Kconfig"
|
||
|
|
|
||
|
|
source "arch/arm/mach-highbank/Kconfig"
|
||
|
|
|
||
|
|
source "arch/arm/mach-integrator/Kconfig"
|
||
|
|
|
||
|
|
source "arch/arm/mach-k3/Kconfig"
|
||
|
|
|
||
|
|
source "arch/arm/mach-keystone/Kconfig"
|
||
|
|
|
||
|
|
source "arch/arm/mach-kirkwood/Kconfig"
|
||
|
|
|
||
|
|
source "arch/arm/cpu/arm926ejs/lpc32xx/Kconfig"
|
||
|
|
|
||
|
|
source "arch/arm/mach-mvebu/Kconfig"
|
||
|
|
|
||
|
|
source "arch/arm/cpu/armv7/ls102xa/Kconfig"
|
||
|
|
|
||
|
|
source "arch/arm/mach-imx/mx2/Kconfig"
|
||
|
|
|
||
|
|
source "arch/arm/mach-imx/mx3/Kconfig"
|
||
|
|
|
||
|
|
source "arch/arm/mach-imx/mx5/Kconfig"
|
||
|
|
|
||
|
|
source "arch/arm/mach-imx/mx6/Kconfig"
|
||
|
|
|
||
|
|
source "arch/arm/mach-imx/mx7/Kconfig"
|
||
|
|
|
||
|
|
source "arch/arm/mach-imx/mx7ulp/Kconfig"
|
||
|
|
|
||
|
|
source "arch/arm/mach-imx/imx8/Kconfig"
|
||
|
|
|
||
|
|
source "arch/arm/mach-imx/imx8m/Kconfig"
|
||
|
|
|
||
|
|
source "arch/arm/mach-imx/mxs/Kconfig"
|
||
|
|
|
||
|
|
source "arch/arm/mach-omap2/Kconfig"
|
||
|
|
|
||
|
|
source "arch/arm/cpu/armv8/fsl-layerscape/Kconfig"
|
||
|
|
|
||
|
|
source "arch/arm/mach-orion5x/Kconfig"
|
||
|
|
|
||
|
|
source "arch/arm/mach-owl/Kconfig"
|
||
|
|
|
||
|
|
source "arch/arm/mach-rmobile/Kconfig"
|
||
|
|
|
||
|
|
source "arch/arm/mach-meson/Kconfig"
|
||
|
|
|
||
|
|
source "arch/arm/mach-mediatek/Kconfig"
|
||
|
|
|
||
|
|
source "arch/arm/mach-qemu/Kconfig"
|
||
|
|
|
||
|
|
source "arch/arm/mach-rockchip/Kconfig"
|
||
|
|
|
||
|
|
source "arch/arm/mach-s5pc1xx/Kconfig"
|
||
|
|
|
||
|
|
source "arch/arm/mach-snapdragon/Kconfig"
|
||
|
|
|
||
|
|
source "arch/arm/mach-socfpga/Kconfig"
|
||
|
|
|
||
|
|
source "arch/arm/mach-sti/Kconfig"
|
||
|
|
|
||
|
|
source "arch/arm/mach-stm32/Kconfig"
|
||
|
|
|
||
|
|
source "arch/arm/mach-stm32mp/Kconfig"
|
||
|
|
|
||
|
|
source "arch/arm/mach-sunxi/Kconfig"
|
||
|
|
|
||
|
|
source "arch/arm/mach-tegra/Kconfig"
|
||
|
|
|
||
|
|
source "arch/arm/mach-uniphier/Kconfig"
|
||
|
|
|
||
|
|
source "arch/arm/cpu/armv7/vf610/Kconfig"
|
||
|
|
|
||
|
|
source "arch/arm/mach-zynq/Kconfig"
|
||
|
|
|
||
|
|
source "arch/arm/mach-versal/Kconfig"
|
||
|
|
|
||
|
|
source "arch/arm/mach-zynqmp-r5/Kconfig"
|
||
|
|
|
||
|
|
source "arch/arm/cpu/armv7/Kconfig"
|
||
|
|
|
||
|
|
source "arch/arm/cpu/armv8/zynqmp/Kconfig"
|
||
|
|
|
||
|
|
source "arch/arm/cpu/armv8/Kconfig"
|
||
|
|
|
||
|
|
source "arch/arm/mach-imx/Kconfig"
|
||
|
|
|
||
|
|
source "board/bosch/shc/Kconfig"
|
||
|
|
source "board/CarMediaLab/flea3/Kconfig"
|
||
|
|
source "board/Marvell/aspenite/Kconfig"
|
||
|
|
source "board/Marvell/gplugd/Kconfig"
|
||
|
|
source "board/armadeus/apf27/Kconfig"
|
||
|
|
source "board/armltd/vexpress/Kconfig"
|
||
|
|
source "board/armltd/vexpress64/Kconfig"
|
||
|
|
source "board/broadcom/bcm23550_w1d/Kconfig"
|
||
|
|
source "board/broadcom/bcm28155_ap/Kconfig"
|
||
|
|
source "board/broadcom/bcm968580xref/Kconfig"
|
||
|
|
source "board/broadcom/bcmcygnus/Kconfig"
|
||
|
|
source "board/broadcom/bcmnsp/Kconfig"
|
||
|
|
source "board/broadcom/bcmns2/Kconfig"
|
||
|
|
source "board/cavium/thunderx/Kconfig"
|
||
|
|
source "board/cirrus/edb93xx/Kconfig"
|
||
|
|
source "board/eets/pdu001/Kconfig"
|
||
|
|
source "board/emulation/qemu-arm/Kconfig"
|
||
|
|
source "board/freescale/ls2080a/Kconfig"
|
||
|
|
source "board/freescale/ls2080aqds/Kconfig"
|
||
|
|
source "board/freescale/ls2080ardb/Kconfig"
|
||
|
|
source "board/freescale/ls1088a/Kconfig"
|
||
|
|
source "board/freescale/ls1021aqds/Kconfig"
|
||
|
|
source "board/freescale/ls1043aqds/Kconfig"
|
||
|
|
source "board/freescale/ls1021atwr/Kconfig"
|
||
|
|
source "board/freescale/ls1021aiot/Kconfig"
|
||
|
|
source "board/freescale/ls1046aqds/Kconfig"
|
||
|
|
source "board/freescale/ls1043ardb/Kconfig"
|
||
|
|
source "board/freescale/ls1046ardb/Kconfig"
|
||
|
|
source "board/freescale/ls1012aqds/Kconfig"
|
||
|
|
source "board/freescale/ls1012ardb/Kconfig"
|
||
|
|
source "board/freescale/ls1012afrdm/Kconfig"
|
||
|
|
source "board/freescale/mx35pdk/Kconfig"
|
||
|
|
source "board/freescale/s32v234evb/Kconfig"
|
||
|
|
source "board/grinn/chiliboard/Kconfig"
|
||
|
|
source "board/gumstix/pepper/Kconfig"
|
||
|
|
source "board/h2200/Kconfig"
|
||
|
|
source "board/hisilicon/hikey/Kconfig"
|
||
|
|
source "board/hisilicon/poplar/Kconfig"
|
||
|
|
source "board/isee/igep003x/Kconfig"
|
||
|
|
source "board/phytec/pcm051/Kconfig"
|
||
|
|
source "board/silica/pengwyn/Kconfig"
|
||
|
|
source "board/spear/spear300/Kconfig"
|
||
|
|
source "board/spear/spear310/Kconfig"
|
||
|
|
source "board/spear/spear320/Kconfig"
|
||
|
|
source "board/spear/spear600/Kconfig"
|
||
|
|
source "board/spear/x600/Kconfig"
|
||
|
|
source "board/st/stv0991/Kconfig"
|
||
|
|
source "board/tcl/sl50/Kconfig"
|
||
|
|
source "board/ucRobotics/bubblegum_96/Kconfig"
|
||
|
|
source "board/birdland/bav335x/Kconfig"
|
||
|
|
source "board/toradex/colibri_pxa270/Kconfig"
|
||
|
|
source "board/vscom/baltos/Kconfig"
|
||
|
|
source "board/woodburn/Kconfig"
|
||
|
|
source "board/xilinx/Kconfig"
|
||
|
|
source "board/xilinx/zynq/Kconfig"
|
||
|
|
source "board/xilinx/zynqmp/Kconfig"
|
||
|
|
source "board/zipitz2/Kconfig"
|
||
|
|
|
||
|
|
source "arch/arm/Kconfig.debug"
|
||
|
|
|
||
|
|
endmenu
|
||
|
|
|
||
|
|
config SPL_LDSCRIPT
|
||
|
|
default "arch/arm/cpu/arm926ejs/mxs/u-boot-spl.lds" if (ARCH_MX23 || ARCH_MX28) && !SPL_FRAMEWORK
|
||
|
|
default "arch/arm/cpu/arm1136/u-boot-spl.lds" if CPU_ARM1136
|
||
|
|
default "arch/arm/cpu/armv8/u-boot-spl.lds" if ARM64
|
||
|
|
|
||
|
|
|