146 lines
2.9 KiB
C
146 lines
2.9 KiB
C
// SPDX-License-Identifier: GPL-2.0+
|
|
/*
|
|
* Copyright (C) 2016 Stefan Roese <sr@denx.de>
|
|
*/
|
|
|
|
#include <common.h>
|
|
#include <dm.h>
|
|
#include <fdtdec.h>
|
|
#include <linux/libfdt.h>
|
|
#include <linux/sizes.h>
|
|
#include <pci.h>
|
|
#include <asm/io.h>
|
|
#include <asm/system.h>
|
|
#include <asm/arch/cpu.h>
|
|
#include <asm/arch/soc.h>
|
|
#include <asm/armv8/mmu.h>
|
|
|
|
DECLARE_GLOBAL_DATA_PTR;
|
|
|
|
/*
|
|
* Not all memory is mapped in the MMU. So we need to restrict the
|
|
* memory size so that U-Boot does not try to access it. Also, the
|
|
* internal registers are located at 0xf000.0000 - 0xffff.ffff.
|
|
* Currently only 2GiB are mapped for system memory. This is what
|
|
* we pass to the U-Boot subsystem here.
|
|
*/
|
|
#define USABLE_RAM_SIZE 0x80000000
|
|
|
|
ulong board_get_usable_ram_top(ulong total_size)
|
|
{
|
|
if (gd->ram_size > USABLE_RAM_SIZE)
|
|
return USABLE_RAM_SIZE;
|
|
|
|
return gd->ram_size;
|
|
}
|
|
|
|
/*
|
|
* On ARMv8, MBus is not configured in U-Boot. To enable compilation
|
|
* of the already implemented drivers, lets add a dummy version of
|
|
* this function so that linking does not fail.
|
|
*/
|
|
const struct mbus_dram_target_info *mvebu_mbus_dram_info(void)
|
|
{
|
|
return NULL;
|
|
}
|
|
|
|
/* DRAM init code ... */
|
|
|
|
#define MV_SIP_DRAM_SIZE 0x82000010
|
|
|
|
static u64 a8k_dram_scan_ap_sz(void)
|
|
{
|
|
struct pt_regs pregs;
|
|
|
|
pregs.regs[0] = MV_SIP_DRAM_SIZE;
|
|
pregs.regs[1] = SOC_REGS_PHY_BASE;
|
|
smc_call(&pregs);
|
|
|
|
return pregs.regs[0];
|
|
}
|
|
|
|
static void a8k_dram_init_banksize(void)
|
|
{
|
|
/*
|
|
* The firmware (ATF) leaves a 1G whole above the 3G mark for IO
|
|
* devices. Higher RAM is mapped at 4G.
|
|
*
|
|
* Config 2 DRAM banks:
|
|
* Bank 0 - max size 4G - 1G
|
|
* Bank 1 - ram size - 4G + 1G
|
|
*/
|
|
phys_size_t max_bank0_size = SZ_4G - SZ_1G;
|
|
|
|
gd->bd->bi_dram[0].start = CONFIG_SYS_SDRAM_BASE;
|
|
if (gd->ram_size <= max_bank0_size) {
|
|
gd->bd->bi_dram[0].size = gd->ram_size;
|
|
return;
|
|
}
|
|
|
|
gd->bd->bi_dram[0].size = max_bank0_size;
|
|
if (CONFIG_NR_DRAM_BANKS > 1) {
|
|
gd->bd->bi_dram[1].start = SZ_4G;
|
|
gd->bd->bi_dram[1].size = gd->ram_size - max_bank0_size;
|
|
}
|
|
}
|
|
|
|
int dram_init_banksize(void)
|
|
{
|
|
if (CONFIG_IS_ENABLED(ARMADA_8K))
|
|
a8k_dram_init_banksize();
|
|
else
|
|
fdtdec_setup_memory_banksize();
|
|
|
|
return 0;
|
|
}
|
|
|
|
int dram_init(void)
|
|
{
|
|
if (CONFIG_IS_ENABLED(ARMADA_8K)) {
|
|
gd->ram_size = a8k_dram_scan_ap_sz();
|
|
if (gd->ram_size != 0)
|
|
return 0;
|
|
}
|
|
|
|
if (fdtdec_setup_mem_size_base() != 0)
|
|
return -EINVAL;
|
|
|
|
return 0;
|
|
}
|
|
|
|
int arch_cpu_init(void)
|
|
{
|
|
/* Nothing to do (yet) */
|
|
return 0;
|
|
}
|
|
|
|
int arch_early_init_r(void)
|
|
{
|
|
struct udevice *dev;
|
|
int ret;
|
|
int i;
|
|
|
|
/*
|
|
* Loop over all MISC uclass drivers to call the comphy code
|
|
* and init all CP110 devices enabled in the DT
|
|
*/
|
|
i = 0;
|
|
while (1) {
|
|
/* Call the comphy code via the MISC uclass driver */
|
|
ret = uclass_get_device(UCLASS_MISC, i++, &dev);
|
|
|
|
/* We're done, once no further CP110 device is found */
|
|
if (ret)
|
|
break;
|
|
}
|
|
|
|
/* Cause the SATA device to do its early init */
|
|
uclass_first_device(UCLASS_AHCI, &dev);
|
|
|
|
#ifdef CONFIG_DM_PCI
|
|
/* Trigger PCIe devices detection */
|
|
pci_init();
|
|
#endif
|
|
|
|
return 0;
|
|
}
|